Pre-Commissioning: Steam Blowing and Chemical cleaning of Oil Refinery Plant's pipeline systems (Future Growth Project (FGP)), Tengiz Oil Field ❖ In Cooperation with Engineering Team control over of Process Pipeline Packs walkdown before the start of Water flushing, Air Blowing and Steam Blowing work activities. ❖ Control over the Correct installation of Pipeline as per created Packs for Chemical Cleaning processes. ❖ Creating the Technical Query form for the temporary pipelines points, which are faced with the problem during the installation activities. ❖ Involved to Walkdown activities for Chemical Cleaning of process pipelines. ❖ Involved to Mechanical Completion of Process Pipelines for Steam Blow Activities. ❖ Control Over the correct installation of Temporary Pipelines, which are need to process of Chemical Cleaning, Air Blowing, Water flushing and Steam Blowing processes of Pipelines. ❖ In Cooperation with Engineering Team responsible for the development of temporary piping isometric drawings ❖ In Cooperation with Project Engineers responsible for the development of spool fabrication drawings, along with preparing detailed bills of materials. ❖ Involved to process of generate composite process flow diagrams (PFDs) from our clients detailed P&IDs. ❖ Involved to assist project engineers with reviewing client isometrics, summarize system configurations in preparation of input into fluid flow analysis software. ❖ In Cooperation with QC Department the inspection control for Chemical and Air Hoses conditions and sending the not passed visual inspection ones for Hydraulic test procedure ❖ Preparation of Test pack and Procedures for Hydraulic test procedure for New Entered Hoses and Special Pipe Spools, which need to be tested as per client requests. ❖ Control of Hydraulic and Leak test work activities of Special Pipelines for Steam Blow Process and Control of Leak Test Procedure for Valves. ❖ Working for control of mechanical completion of Process pipelines with P&ID for Cleaning with hydro milling high pressure units Aqualizing cleaning work activities. ❖ Inspection of equipment status and conditions, which were involved for Steam Blowing and Chemical Cleaning Process (Potable Boiler Room (from RH-250 till RH-1500 Heating Power), Aqualizing Units, Pulse Flush Units, Air Dryers, Air Receiver Tanks, Generators, Compressors, Mix Tanks, Dry Silencers, Wet Suppressors, Circulation Pumps, Chemical Tote Tanks, Diaphragm pumps, Standalone Filter Skids, Heat Exchangers and setra) and sending for repair the damaged and not works ones. ❖ Daily Inspection control of Gauges, which are in use at construction site, (Pressure gauges, Temperature Gauges and Setra) in cooperation with QC department and sending the not passed the visual inspection ones to recalibration procedure to laboratory. ❖ In Cooperation with Field Engineers providing the other type of materials, which are available and in stock at warehouse, for installation points, which are faced with Site Condition Modifications and not installable the design Project Fittings and materials for further action without lack of Pipeline Implementation process. ❖ Timely control of gauges' calibration dates, which was stored in Warehouse, for keeping them ready for installation, Gauges (PG, TG, Flowmeters, Pressure Trolleys and Setra) which calibration date are close to end, preparation of them to sending for calibrating procedure. ❖ In Cooperation with the Planning/Engineering Team creating the Purchase List for Project Materials, which will be need for Construction Activities of temporary pipelines for Steam Blow and Chemical Cleaning process.

Kazakhstan Caspian Offshore Industries (Turnaround 2022 FSSA), Reinstallation of 30 inch Amine Lines (Turnaround 2022) on the Oil Refinery Plant Bolashak, Karabatano Eskene West. ❖ Daily work activities and duties was as below (all activities main purpose as " work without loss of productivity workhours in teamwork with all departments with the saving of HSE requirements for successful finish of Turnaround Campaign in time): ❖ Control over the Hydrotest packs creation procedure of finished the installation of Pipelines. ❖ Control over the equipment for Hydraulic test activities. ❖ Involved to prepare the technical reports, lists of outstanding items on a punch list submits it for construction to carry out the required test. ❖ Involved to process of monitoring the hydro testing (hydrostatic and pneumatic) and handling reports on the completion of tests and to supervising line cleaning after hydro test. ❖ Involved for the examination of systems to ensure completeness, punch lists preparation, and readiness for hydro tests activities. ❖ In cooperation with Engineering team involved for Walkdown of finished process pipeline for preparation of hydraulic test procedure ❖ In connection with the Planning Team the creation of Purchase List of Consumable and Project Materials, which will be necessary for installation of Pipeline. When the Engineering Team during the Installation of Pipeline was faced with problems of not suitable for installing the project Material: in Cooperation with Lead Engineers Creating the Material Approval Request for available in stock materials for further action and immediately continue of Construction Activities for not losing of Productivity time with the saving of Quality requirements. ❖ Inspection Control of All Rental equipment and sending to the Vendor of damaged ones with further action and for making the replacement for Working ones without loss of effectively work time. ❖ Inspection of gauges for Calibration Dates and sending the of Expired ones to Calibration Procedure.

SK "Senimdi Kurylys", Supply chain of Materials Management for Future Growth Project (3GP), Tengiz Oil Field ❖ Control over of Equipment and Pipeline materials and valves supplies the correct entry as per ISO Drawings. ❖ Inspection for new entered Special Custom Pipelines for correct supply as per ISO Drawings ❖ Inspection for NDT test certificates of Project Pipelines’ welding joints ❖ Inspection for equipment of Hydraulic Test activities. ❖ Control over the correct entry as per ASTM standards of all equipment for Hydraulic test. ❖ Checking the material received at the warehouse for compliance with the requirements of quality standards. ❖ Checking the availability of a set of documents for materials used for construction, structural elements and equipment. ❖ Study of the results obtained during the implementation of the incoming control of the design material, as well as acts of laboratory tests for the received material.

Project: construction of the Combined Cycle Power Plant (capacity - 310 Megawatts) on the Karabatan industrial area. Implementation on behalf of the contractor construction control over the performance of construction and installation works and verification of installed equipment. Control over the implementation of capital construction plans, compliance with the scope, timing and quality of construction and installation works, as well as the quality of materials, products, designs of approved design estimates, working drawings, construction norms and rules, standards, technical conditions, labor protection regulations. I spend daily bypassing the construction site to monitor the progress of construction, namely: • Control of equipment installation according to the project. • To identify the necessary changes to continue construction. • Using my experience and skills, I give recommendations to the construction and installation team to eliminate the deficiencies. • In the places of problems with the installation of technological pipelines, I create a technical request to the customer to make changes to the design data in order to continue the construction process. All decisions on making changes should be made within the framework of the standards of the Republic of Kazakhstan, and therefore has the case that it is necessary to take into account all factors. • By measuring the distance from metal structures to TX pipelines, I create drawings for the manufacture of supports from channels, angles, I-beams. Before issuing the created drawings to the production department, I make calculations for the stress resistance of these supports relative to the mass of the pipeline load, which depends on the wall thickness, type of material, length of the pipeline, its diameter in inches. • Checking compliance with all conditions in the paint shop, according to the flow chart. Check the relative humidity, temperature, drying time, the thickness of the painting. Creating a list of paints and solvents required for painting pipelines depending on the system and on the presence of insulation, you must give instructions on the type of color painting. Participation in the decision on issues related to the introduction of changes in the projects in connection with the introduction of more advanced technological processes, volumetric-planning and constructive solutions that ensure cost reduction and improvement of technical and economic indicators of construction and reconstruction facilities. I take part in the review and approval of the project design changes arising during the construction, I solve the issues of replacing materials, products, and structures, if necessary, without reducing the quality of the construction projects. The study of the causes causing the failure of the timing and deterioration of the quality of construction and installation work, I take measures to prevent and eliminate them. Implementation of technical acceptance of completed construction and installation works and facilities, registration of necessary technical documentation. Participation in the work of commissions for the acceptance of construction materials and their delivery for installation works (RSI). Request for stored item. Control of quality of elimination by construction and installation teams of imperfections, defects in the established terms. Keeping records of completed construction and installation works and preparing the necessary data for reporting on the implementation of capital construction plans.

Conducting market analysis, investment attractiveness of certain financial instruments, regarding the possibility of opening transactions, according to the business process of market analysis and the Regulation on Risks. On an ongoing basis, an operation to buy / sell assets in financial markets in order to obtain income on invested capital, according to the signals of its trading system. Compliance with the rules of regulations on risks and transaction procedures, according to the developed business processes. Conducting a trader's trading log according to the approved form. Conducting analysis of concluded deals, their results according to existing business processes. Maintenance of graphical log of account balance changes, transaction statistics. Based on the analysis of trading activities, the development of measures to normalize the risks of invested capital, increase the yield of individual trades and the totality of trades over the period. Providing positive profitability for trading activities for the reporting period (month, quarter). In the event that the profits for invested capital are not received during the trading period or when a loss is received within the limits of the allowable drawdowns, a detailed analysis of the causes and the plan of measures for their elimination is prepared. In the event of receiving a drawdown over the trading period above the permissible, the suspension of its activities for up to one month, with a review of the situation and the transition of trades to a demo account. Informing interested persons (investors) about current profitability, possible risks, development of individual investment plans together with them. Trading with assets on the Forex platform.

I worked with regular customers-consumers of goods. Work's purpose: aimed at maximum satisfaction of their needs and support of long-term cooperation.

Oil and Gas, Technique and technology of petroleum engineering

LLP "WWS", Safe operation of pressure vessels

Language center of the KIMEP university, Preparing to pass the IELTS (International English Language Testing System)